Kansas DOV CDL General Knowledge Practice Test 1
Test 1 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Kansas test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. What is the purpose of the torque rods or radius rods you check on the suspension?
Show answer
Answer A: They hold the axle in alignment with the frame under braking and acceleration
Torque rods resist the twisting and fore and aft forces on the axle, so a cracked or missing rod lets the axle move out of alignment.
-
2. Which description matches controlled braking during an emergency stop?
Show answer
Answer D: Apply the brakes as hard as you can without locking the wheels and keep steering movements small
Controlled braking keeps the wheels rolling just short of lockup, which gives the shortest stop while you keep the ability to steer.
-
3. Why should you never shift gears while crossing railroad tracks?
Show answer
Answer A: You could miss the gear or stall and be stuck on the tracks
A stalled or coasting vehicle on the tracks has no way to clear quickly, so choose the gear before the crossing and do not shift until you are across.
-
4. What should you check about the air hoses and the electrical cord running to the trailer?
Show answer
Answer D: That they are free of damage, properly connected and not dragging or rubbing
Lines that chafe on the frame or drag on the road wear through, and a broken line takes away trailer braking or trailer lighting without warning.
-
5. Part of your load stands high enough to hide a rear lamp or a reflector. What must be done?
Show answer
Answer B: The load must be moved or extra lamps fitted so the required lights can be seen
Required lamps and reflectors must remain visible; if the cargo blocks them, the load is rearranged or additional lamps are fitted so the vehicle can still be seen.
-
6. After starting a trip, when must a driver first re-inspect the cargo and the devices holding it?
Show answer
Answer A: Within the first 50 miles
Federal rules require a check of the load and its securement within the first 50 miles, because settling and vibration loosen straps and chains early in a trip.
-
7. Why should a driver avoid stopping partway up a snow covered hill?
Show answer
Answer D: You may not get moving again and could slide backwards
On a slippery grade the drive wheels may simply spin when you try to restart, leaving the vehicle stuck across the road or sliding back down it.
-
8. A roadside test shows a commercial driver has measurable alcohol in the system but below 0.04. What happens?
Show answer
Answer C: The driver is placed out of service for 24 hours
Any measurable alcohol while on duty results in an immediate 24 hour out of service order, even when the concentration is under the 0.04 limit.
-
9. What is the correct way to make a right turn in a long vehicle?
Show answer
Answer D: Keep the rear of the vehicle close to the curb and swing wide only as you complete the turn
Swinging left before a right turn invites another driver to move into the gap on your right, so any extra width is taken as the turn is finished.
-
10. What training does Kansas require before it will issue or renew a commercial driver's license?
Show answer
Answer D: Training in human trafficking identification and prevention
K.S.A. 8-2,157 requires every commercial license applicant to finish attorney general approved training in human trafficking identification and prevention.
-
11. Why should you avoid using your lights to tell a following driver that it is safe to pass you?
Show answer
Answer B: You may misjudge the gap and the driver will act on your signal
The manual warns against signaling others to pass, because the responsibility for a head-on crash then rests on a judgment you could easily get wrong.
-
12. You are about to slow down sharply on a highway to make a turn into a narrow driveway. How can you warn the drivers behind you?
Show answer
Answer C: Tap the brake pedal a few times so the brake lights flash before you slow down
A few light taps flash the brake lights and give following drivers an early warning that you are about to slow or stop.
-
13. Two vehicles of exactly the same length make a right turn, one gently and one very tightly. What is the effect on off-tracking?
Show answer
Answer A: Turning more sharply increases off-tracking, so the tight turn needs more room
Off-tracking depends on both the length of the vehicle and the sharpness of the turn; a tighter corner brings the rear wheels further inside the path of the front wheels.
-
14. Why must exhaust components be checked for contact with other parts of the vehicle?
Show answer
Answer B: Hot exhaust parts touching fuel lines, tires or wiring can start a fire
Exhaust pipes run hot enough to ignite fuel and melt insulation, so they must be kept clear of the fuel system, the tires and the electrical harness.
-
15. An empty van trailer cleared a low overpass on the way in, but on the way back it is loaded. Which statement is true?
Show answer
Answer C: An empty van rides higher than a loaded one, so it needs more clearance than when loaded
Springs compress under load, so an empty trailer is taller; the unloaded trip is the one that can catch a low overhead.
-
16. What is the minimum tread depth for tires in positions other than the steering axle?
Show answer
Answer A: 2/32 inch
Drive and trailer tires must keep at least 2/32 inch of tread in a major groove, measured away from tie bars and fillets.
-
17. What extinguisher rating is required on a vehicle carrying hazardous materials in amounts that need placards?
Show answer
Answer B: 10 B:C or more
Placarded loads carry a much higher fire risk, so the required extinguisher rating rises to at least 10 B:C.
-
18. Which industries may use a Kansas seasonal commercial driver's license?
Show answer
Answer C: Farm retail outlets and suppliers, agri-chemical businesses, custom harvesters, and livestock feeders
K.S.A. 8-2,146 limits the seasonal commercial driver's license to commercial vehicles owned by farm retail outlets and suppliers, agri-chemical businesses, custom harvesters, and livestock feeders.
-
19. Loading heavy freight on top of lighter freight has what effect on the vehicle?
Show answer
Answer B: It raises the center of gravity and makes a rollover more likely
A high center of gravity lets the vehicle tip more easily in curves or during a sudden swerve.
-
20. The shipper hands you the placards for a load that needs them. Who puts them on the vehicle?
Show answer
Answer C: The driver, who must also make sure they are the correct ones and are readable
The shipper supplies the placards, but it is the driver who must place them on the vehicle and confirm that they match the load and can be read.
-
21. A straight truck has a long body behind the rear axle. What happens to that overhang in a sharp left turn?
Show answer
Answer D: It swings out to the right and can strike a vehicle or an object on that side
Body that hangs behind the rear axle swings the opposite way to the turn, so the tail of the truck sweeps out into the next lane or over the curb.
-
22. Which factors determine a safe speed for a long, steep downgrade?
Show answer
Answer C: The steepness and length of the grade, the weight of the vehicle and cargo, and the road and weather conditions
Gravity, weight and traction all decide how fast a heavy vehicle can safely descend, which is why signs often post lower speeds for trucks on grades.
-
23. On the Interstate System, what are the federal maximums for a tandem axle group and for gross vehicle weight?
Show answer
Answer B: 34,000 pounds and 80,000 pounds
The federal Interstate limits allow 34,000 pounds on a tandem axle group and 80,000 pounds gross.
-
24. You find a defect during the pre-trip inspection. What must happen before the vehicle is driven?
Show answer
Answer C: It must be repaired, or the vehicle must not be driven
Writing a defect down does not make the vehicle safe; a defect that affects safe operation has to be corrected before the trip starts.
-
25. At 55 mph, about how far does a vehicle travel during a typical 3/4 second perception time plus 3/4 second reaction time, before the brakes even begin to work?
Show answer
Answer C: About 120 feet
Each 3/4 second at 55 mph covers about 60 feet, so perception and reaction together use up roughly 120 feet before braking starts.
-
26. Which lamp must make the rear registration plate legible after dark?
Show answer
Answer C: A white lamp that lights the plate
A white license plate lamp is required so the plate can be read at night, and a burned out one is a defect like any other lamp.
-
27. You are given a ratchet strap with a deep cut along one edge. What should you do?
Show answer
Answer C: Do not use it; a damaged tiedown cannot be relied on to hold its rated load
Cuts, burns, knots and broken stitching weaken a strap far below its marked working load limit, so it must be taken out of service.
-
28. How are the headlights, marker lights and turn signals checked during the seven-step inspection?
Show answer
Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle
The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.
-
29. The only way into a customer yard forces you to back toward the right, or blind, side of the vehicle. What should you do?
Show answer
Answer D: Use a helper and get out to check the path more often than you normally would
Blind side backing is allowed but far riskier, so it calls for a spotter you can see and for repeated checks of the path on foot.
-
30. What must the driver check about the seat belt during the inspection?
Show answer
Answer A: That it is securely mounted, adjusts properly and is not ripped or frayed
A belt only restrains the driver if its anchorage is sound and the webbing is intact, so mounting and condition are both checked.
-
31. The rear wheels of your vehicle lock during braking and the rear starts to slide sideways. What should you do first?
Show answer
Answer A: Stop braking so the rear wheels can roll again, then steer quickly in the direction you want to go
Locked wheels have no side grip; releasing the brakes restores traction and then countersteering brings the vehicle back into line.
-
32. Why is braking while in a curve dangerous in a heavy vehicle?
Show answer
Answer A: The wheels lock more easily and the vehicle can skid
Tires already using their grip to turn have little left for braking, so hard braking in a curve locks the wheels; slow down before the curve instead.
-
33. Which combination of warning devices meets the requirement for a stopped commercial vehicle?
Show answer
Answer A: Three reflective triangles, or six fusees, or three liquid burning flares
A vehicle may carry three bidirectional reflective triangles, six fusees or three liquid burning flares as its warning devices.
-
34. The brake pedal goes to the floor in a vehicle with hydraulic brakes. What can you do to build some braking pressure?
Show answer
Answer B: Pump the brake pedal rapidly, which may bring back enough pressure to slow the vehicle
Pumping can restore some hydraulic pressure; along with downshifting and the parking brake it is one of the ways to stop when the pedal fails.
-
35. What does a front-end header board on a van or flatbed protect against?
Show answer
Answer A: Cargo moving forward toward the cab in a crash or hard stop
The header board, often called a headache rack, blocks forward movement of the load toward the driver.
-
36. You are the first to arrive at a crash. What is the correct order of actions?
Show answer
Answer C: Protect the area, notify the authorities, care for the injured
Preventing a second crash comes first, because an unprotected scene puts the injured and the helpers in more danger than the original collision.
-
37. When should a driver select the gear for a long, steep downgrade?
Show answer
Answer B: Before starting down the grade
The low gear has to be chosen before the descent, because a heavy vehicle gaining speed may refuse to shift down at all.
-
38. Why should a retarder be switched off when the road is wet, icy or snowy?
Show answer
Answer C: It can make the drive wheels skid when traction is poor
A retarder slows the drive wheels only, and on a slippery surface that braking force can break their traction and start a skid.
-
39. What condition should the fifth wheel be in before you back under a trailer?
Show answer
Answer C: Jaws open, plate greased, and the fifth wheel tilted down toward the rear
The jaws have to be open to take the kingpin, the plate must be lubricated to prevent hard steering, and the fifth wheel is tilted down at the rear so the trailer apron can ride up onto it.
-
40. When should mirror adjustment be checked, and what should each mirror show?
Show answer
Answer B: Before every trip, with each mirror adjusted to show some part of the vehicle
Checking the mirrors before each trip and keeping a small part of the vehicle in view gives a reference point for judging distance behind and beside you.
-
41. You need fuel and the canopy over the pumps is low. What is the safe way to handle the clearance?
Show answer
Answer B: Stop and check the height at the entrance and at the way out before committing
Clearance can differ at the entry, under the canopy and at the exit, and a sloping approach changes the effective height, so both ends have to be checked.
-
42. A dispatcher tells you to take a trailer you believe is loaded badly enough to be unsafe. What should you do?
Show answer
Answer C: Refuse to move it until the load has been made safe
The driver may not operate a vehicle whose cargo is not properly distributed and secured, and an instruction from an employer does not change that.
-
43. Part of looking well ahead is planning an out. What does that mean?
Show answer
Answer B: Keeping an escape path in mind in case traffic stops suddenly
Because a heavy vehicle often cannot stop in time, good drivers continuously note where they could steer if the space ahead closes.
-
44. What does the working load limit stamped on a chain or strap describe?
Show answer
Answer B: The maximum load the device is rated to hold in normal use
The working load limit is the rated safe capacity for everyday use, deliberately set well below the force that would break the device.
-
45. A strap runs from an anchor point on one side of the trailer, over the load, and down to an anchor point on the opposite side. How much of its working load limit counts toward the total required?
Show answer
Answer C: All of it
A tiedown that is anchored on one side, passes over or around the cargo and is anchored on the other side counts its full working load limit toward the aggregate figure.
-
46. What frame defects are you looking for during the walkaround?
Show answer
Answer A: Cracks, bends or broken cross members
The frame carries the whole load, so cracked or bent rails and broken cross members are serious structural defects.
-
47. Within total stopping distance, what exactly is perception distance?
Show answer
Answer D: The distance traveled from the moment your eyes see a hazard until your brain identifies it
Perception distance covers only the time between seeing a hazard and recognizing it as a hazard, before any physical reaction begins.
-
48. How do you confirm that the coupling is locked before pulling out of the yard?
Show answer
Answer D: By locking the trailer brakes and pulling gently forward against them
The tug test loads the coupling in the direction that would pull it apart, so if the jaws are not closed on the kingpin you find out at walking pace.
-
49. You drive a 40 foot straight truck at 50 miles per hour in good conditions. What following distance does the rule of thumb call for?
Show answer
Answer A: 5 seconds
One second for every 10 feet of vehicle length gives 4 seconds, and one extra second is added for speeds above 40 miles per hour.
-
50. How long must a motor carrier keep a driver vehicle inspection report and the certification of repairs?
Show answer
Answer B: Three months
The original report and the certifications attached to it are kept on file for three months from the date the report was prepared.